The DA14531 SmartBond TINY™ Module is the Bluetooth® low energy solution that will power the next 1 billion IoT devices through ease of use.
The DA14531 SmartBond TINY™ Module, based on the world’s smallest and lowest power Bluetooth 5.1 system-on-Chip, brings the DA14531 SoC advantages to an integrated module. It just requires a power supply and a printed circuit board to build a Bluetooth application.
该模块的目标是广泛的市场使用，并将跨地区认证，大大节省了开发成本和上市时间。
它配备了一个集成天线和易于使用的软件，使蓝牙低能耗的发展比以往任何时候都更容易。
这一令人敬畏的组合将移动连接带到以前遥不可及的应用程序，通过SmartBond TINY实现下一个10亿个物雷竞技安卓下载联网设备™ 他们的核心。
特征
蓝牙5.1核心
集成天线
全球认证
皮质-M0+@16MHz
IoTMark™-BLE score of 18300
23.75uA/MHz MCU current
记忆: 48kB RAM, 32kB OTP &1Mb FLASH
1.8-3.3V电源范围
+2.2dBM最大输出功率
-93dBm灵敏度
Rx current 2mA at 3V
Tx current 4mA at 3V at 0dBm
强度rfaces: 2xUART, SPI, I2C
4-channel 10-bit ADC
8 GPIO
内置温度传感器
Operating temperature: -40°C to +85°C
尺寸：12.5x14.5x2.8 mm
雷竞技安卓下载
Beacons
遥控器
Proximity tags
玩具
Low power sensors
Bluetooth LE附加组件“管道”到现有应用程序雷竞技安卓下载
提供任何类型的设备，使基于智能手机应用程序的设置和控制易于使用，无需打印用户手册
DA14531框图
Stay connected
直接通过我们的全球销售办事处与我们联系，或联系我们的全球分销商和代表之一。
查询 Distributors and Representatives Register for newslettersOrdering information
DA14531 SmartBond微型模块
- 零件号：DA14531MOD-00F01002
- 尺寸（mm）：12.5x14.5x2.8
- 装运包装数量：1k卷
Bluetooth Low Energy Development Kit Pro for DA14531
- Part number: DA14531MOD-00DEVKT-P
- Description: Development Kit is based on module samples
Daughterboard for Pro Development Kit
- 零件号：DA14531MOD-00F1DB-P
- Description: DA14531 Module Daughterboard for Pro Development Kit
- SmartBond微型模块：包括主板、子板和电缆；主要用途是软件应用程序开发和功率测量
SmartBond微型模块：包括主板、子板和电缆；
Primary usage is SW application development and power measurements
返回结果
三天前
无法运行DA14531的示例
Posted by独轮滑车85 points 7个答复Duplicated from old forum because the answer may help others:
I've set the dev kit jumpers exactly as described for the "changing advertising method" example. I've compiled the code for the target DA14531. Keil then says "No Cortex-M SW Device Found".
所以我转到了iBeacon的例子。我没有对硬件做任何改动。这个例子上传并运行良好。这有点奇怪。
同样的问题与“广告服务数据”的例子。只是行不通。
有人能解释一下吗？
谢谢。
三天前
嗨，独轮车，
Thanks for your question. Can you please indicate if you are using the DA4531 SoC or the DA14531 TINY module?
对于微型模块，当尝试使用Keil对其编程时，当用户尝试打开调试器会话时可能会发生错误。为了解决这个问题，用户必须将JTAG时钟速度降低到2MHz。
In case this error occurs, please follow the steps described in Section 6.1 Keil JTAG default Clock Speed in UM-B-141 user manual to solve it.
谢谢，下午好
三天前
嗨，独轮车，
This issue is not related to the SW example. If you are using the DA14531 SoC, there is no need to reduce the JTAG speed. As mentioned in my previous comment, this should be done only in the case of DA14531 module.
很高兴你发现了这一点，谢谢你的提示。
谢谢，下午好
三天前
嗨，独轮车，
We'll reach out to you directly (offline from the forum) at your registered email address.
谢谢，下午好
三天前
I found that the project Debug settings had the Max Clock for JLink as 5MHz. Changing it to 2MHz appeared to fix the problem. I can only assume that the example were not tested on the dev board for 531s. This has caused me quite a bit of frustration.