im trying to compile SW Example: Reading out an I2C accelerometer and sending notification data project .but it shows an error .\out_585\ADXL345_585.axf: error: L6031U: Could not open scatter description file .\..\src\config\copied_scatter.sct: No such file or directory. how can i fix thiss error?????????????????????????????
Hello,
我s there any sample apps (or codes) that behave as central mode, connect to peripheral device(s), write without response and receive message through notification?
我don't want to spent time developing code but I could only found BLE Central Security Demo Project below. These are almost peripheral.
https：//www.dialog-seminile.com/produ雷电竞官网登录cts/connectivity/bluetooth-low ...
Thank you in advance.
Using the DA14585/DA14586 BLE Erratum 10734 - security vulnerability from the Dailog portal.
我们遵循了错误中提到的所有步骤。
Facing this error while compiling in Keil:
.\out_585\security_vulnerability_585.axf: error: L3906U: Malformed via file '.\out_585\security_vulnerability_585.lnp'.
Finished: 0 information, 0 warning, 0 error and 1 fatal error messages.
".\out_585\security_vulnerability_585.axf" - 1 Error(s), 1 Warning(s).
Target not created.
我have an issue where bonding to multiple devices is failing. This is very repeatable. Here is how we demonstrate the problem:
1. Pair our DA14585 peripheral to one central device. Connect. All is well. Disconnect.
2. Pair DA14585 to a second central device. Connect. Still fine - communicating with the second device. Disconnect
3. Try to connect to our DA14585 from the first paired device. The DA14585 rejects the connection with LL_REJECT_IND, error code 0x06 “PIN or Key Missing”.
我们正在使用DA14585进行需要的项目和外围角色。在这种情况下，我们需要知道可以在不同状态下执行哪些操作（扫描，启动，连接，广告，待机）。
We cant seem to find it in the SDK documentation for the 6.0.6 SDK, but we have found, that we cant seem to do advertisement while doing a scan (as a central), but we can advertise while we are connected as a central.
Hi Dialog,
Me and a couple of other users has requested information regarding the registers to configure a range extender using different ports/pins than in the examples, see:https://support.dialog-semiconductor.com/forums/post/dialog-smartbond-bl...
Since the thread is marked as "Complete" you might not have noticed, but I'm still in need of the information that was mailed to OP in this thread.
Hi Dialog Team,
我正在使用外部主机模式工作，以及扫描仪/观察模式配置中的BLE。我正在使用带有UART接口的外部主机ST32F4。
我want to add additional functionalities on BLE upon special requests from host.
我had posted similar issue here
https://support.dialog-semiconductor.com/comment/22363
Hi,
My application requires a Bluetooth range from 90-100meter. Can you guide me if DA14585/ 86 is validated with an RF amplifier with a trace antenna?
Can I have the reference design with the above scenarios if already validated?
Thanks in anticipation
Regards
Kinjan
Hi Dialog team,
我am trying to understand how can I add custom handler to the empty_template_ext. Basically we have STM32 as external processor. We are using UART for communication between STM32 and DA14585 with GTL protocol. We want to operate BLE in scanner/observer mode
With the existing code, I could get BD Address, scan for nearby devices. Now to build the application, we are looking for some custom implementation. Say we want to send a command from STM32 to DA14585 to blink LED, read some GPIO status, how can I achieve this.
Hi Dialog ,
