Hello Dialog_support Team,
I am using DA14583 board for development purpose. While flashing the spi using SmartSnippet Studio(Version: 1.6.3.918), i am getting error like "Failed reading memory at address 81FE8".
我跟随下面的链接，但我仍然无法解决这个错误。
https://support.dialog-semiconductor.com/issue-smartsnippet-firmware-dow...
I have attached the pdf file, which shows spi flash error in SmartSnippet Studio.
Please help me out.
Thanks and Regards,
Ruchi Patel
Keywords:
Attachment:
Device:
Hi Ruchi Patel,
On the top of the Smart Snippets tool i see that the tool is not connected to any device,Tracker_flash1@none[DK:DA14583-00], instead of that and if the tool has found a device on the other side of the link should mention either:
Perhaps you should check why that happens, do you select from the initial dialog a proper interface for example ? And if yes which interface is that ?
Thanks MT_dialog
Hello MT_Dialog,
Thanks for the reply. I came to know that device should be connected via either UART or JTAG. So i have tried to connect my device using JTAG and now i am able to see the device is connected liketracker_flash1 @ jtag.. Still i am getting error. I have attached image of SmartSnippet Studio in that you can see error. Please suggest me how to solve this error.
Thanks and Regards,
Ruchi Patel
Hi Ruchi Patel,
我想你正在使用自定义板而不是dev套件，这是正确的吗？请确保VCC_FLASH供电，以便为闪光灯供电。另外尝试重置电路板，然后尝试再次点击“连接”按钮。
Thanks MT_dialog
Dear Dialog_support Team,
Yes i am using custom board. Vcc_flash pin is powered. I have also tried to reset the board before hitting "connect" button but my problem remained same. In Smartsnippet tool, i have selected UART/SPI option to download the code into flash but i got reset related issue. I have attached screenshot of the error. Can you tell me what could be the problem with reset pin?
Thanks and Regards,
Ruchi Patel
Hi Ruchi Patel,
If you have selected the UART/SPI that means that the device will be connected through the UART interface and that means that you would have to connect the RX/TX UART pins, those pins are used in order for the flash programmer to be downloaded into the device during the "Connect" procedure and also thats how the Smart Snippets receives that there was a reset on the device.
Thanks MT_dialog
嗨,我面临着同样的problem as yours. do you know how to resolve this? cause i don't see anything that make me resolve my problem from what the MT_dialog answer. please guide me to resolve this if anyone can resolve this problem.
谢谢.
kind regards
Kevin
Hi Kevleo94,
Please check your other post:
https：//support.dialog-semicondiondiondum/forums/post/dialog-smartbond-bl ...
Thanks MT_dialog
Hello Kevin,
Yes we are able to resolve the problem with the help of Dialog_Support.
我们面临the same issue. You have to make sure few things before burning .hex file into flash.
1.确保您的自定义板的VCC闪存（P0.5-PORT-0 PIN-5）引脚连接VDD。
2. UART Pins P0.4 and P0.5 of custom board must be connected to FTDI Pins(which are right across P0.4 and P0.5 motherboard).
3. Make sure GND and Vcc pins of your custom board must be connected to mother board's ground and Vcc pins respectively.
4. After connecting all these pins using SmartSnippet Studio, you can burn your firmware into flash. (In SmartSnippet Tool, Please select the UART/SPI option-> Upload your .hex file-> press "connect" option -> press "reset" button of your motherboard -> "erase" the flash -> "burn and verify")
Note: we have used DA14580 Pro kit.
hmm.. what is the function of connecting P0.5 to VCC? or do you mean to pull up the Tx and Rx pin?
As per my knowledge, by connecting Vcc_Flash pin to Vdd means enabling the spi_flash pins. DA14583 has internal spi_flash so by connecting vcc_flash pin to vdd, flash pins will enabled.
oh.. i'm sorry. i used da14580. but I'm facing similar problem with you.
如果您不介意，我可以收到您的电子邮件地址吗？所以我可以私下与您联系。谢谢
DA14583 has internal flash but DA14580 does not have internal flash. my email id isruchi.patel35@gmail.com.